How to Carry Spline Clocking Across a Two-Fixture Hub Setup
A hub leaves the first machining fixture with a finished bolt circle and a clear flange face. In the second fixture, the bore is ready for internal spline machining. The operator can locate the bore concentrically yet still cut the spline in the wrong angular relationship to the flange. Centering the hub is not the same as carrying its clocking.
Spline clocking between setups requires a reproducible angular reference, an agreed zero direction and a verification step after the transfer. The drawing must tell the shop how the specified spline tooth space relates to the flange feature, not merely where the bore center lies. The two fixture sketches below turn that requirement into a handoff that a planner and machinist can examine together.
Define the relationship before indexing the second fixture
A drawing may locate the internal spline relative to a flange bolt hole, a pin hole or a designated datum feature. Record which exact feature defines zero, which datum face locates the part axially, and whether the tooth or the tooth space is the controlled angular element. A note that says 'align spline to bolt circle' is incomplete when the bolt circle has equally spaced holes and none is identified as the reference.
For a proposed part, designate a repeatable feature, such as a specially identified flange hole, and document the required angular relationship using the part's own drawing convention. If an orientation mark is added for handling, do not confuse it with a precision datum unless the inspection plan expressly defines and accepts it as one.
Broaching Technologies, LLC describes internal spline broaching, vertical slotting and custom tooling support from its Menomonee Falls, Wisconsin shop. Those are relevant first-party capabilities for a fixture discussion. The company has not provided a specific fixture design, indexing method or verified clocking result for this hypothetical hub, so the transfer plan must be accepted for the actual job.
Two fixtures, one flange reference
Illustrative plan view: Fixture 1 supports a flanged hub during a preceding operation; Fixture 2 locates the same part for indexed spline cutting. Both drawings mark a single reference at the same angular zero. The teal point represents the target tooth-space relationship to check, not a claimed tolerance or actual spline tooth form. The sketches are not to scale or intended as executable machine instructions.
Figure 1 — The orange flange reference defines the same angular zero in both fixtures. A separate teal tooth-space marker is compared to that reference after the transfer. A physical orientation mark can aid handling, but the agreed locating and measurement scheme determines acceptance.
Broaching Technologies’ vertical machining overview is the assigned process reference for this type of indexed internal-profile discussion. The manufacturer's public description is useful context about vertical slotting; it does not state which reference pin, rotary axis, probing method or fixture pair is in use for any particular workpiece.
Fixture 1: establish the starting zero
The first setup needs an unambiguous record of the chosen flange reference and datum face. If a single named hole is used, identify it by drawing callout or distinctive feature; do not select 'the hole nearest the top' from a photograph. Record the revision that defines its angular relationship to the internal spline and note any feature that has not yet been inspected.
A setup sheet might show a locating face, the reference feature and the orientation of the axis used by the first process. For a part that moves later, capture whether the first fixture's zero is a tooling setting, a machined datum, or simply a convention used to present the part. Those are different levels of evidence.
Fixture 2: reproduce or clear re-establish the zero
The second setup must locate the part in a way that can recover the intended angular reference. That might require a keyed locator, a reference feature and indicator, or another shop-approved indexing procedure. The example does not prescribe one; suitable locators depend on the part and available machine. If the first fixture used a face that is not available in the second, state how that datum is transferred or re-established rather than assuming the axis carried through automatically.
A bolt circle can locate an assembly in rotation only if the selected feature and pattern symmetry are considered. Equally spaced holes may permit more than one seemingly correct seating orientation. The fixture designer must account for that ambiguity before the machining program assumes its zero.
Make the first cut or inspection disprove a wrong setup
Put a check in the job plan before processing the balance of the lot: verify the specified spline tooth space against the identified flange reference after the first accepted setup. Record which measurement or qualified inspection method applies, the drawing revision, and the person who can accept the result. A visual paint mark or a remembered table position is not enough to certify an angular requirement.
The check may involve an agreed index measurement, suitable inspection equipment, or functional gaging together with additional angular verification where required. Do not assume that a generic spline plug gauge verifies spline-to-flange clocking. A gauge can establish aspects of fit without revealing the angular relationship to an external flange feature.
If the result fails the specified relationship, stop the planned balance and trace the discrepancy through the drawing, fixture orientation, datum selection, programmed zero and inspection method. Avoid fixing a clocking error by rotating an unverified component and restarting production without a controlled disposition.
Use a transfer record that survives a shift change
For a fictional hub identified H-204, use one transfer line: 'Drawing Rev C; datum face A; flange hole F1 defines zero; target spline space S1 clocked to F1 per approved print; Fixture 1 orientation evidence attached; Fixture 2 zero verification pending; first part held for inspection.' All labels are invented and must be replaced by the actual approved drawing definitions.
The record should also identify the part or lot ID, the two fixture identifiers, any relevant reorientation after transfer, the required inspection and the acceptance owner. It may be brief, but it must not use the word 'aligned' as a substitute for the missing measurement or criteria.
When the fixture is redesigned, the hole pattern changes or the spline callout is revised, treat that as a reason to reassess zero. A later drawing revision cannot be silently applied to a setup sheet created under an earlier one.
Keep bore alignment and angular alignment separate
Bore concentricity, axial face seating and angular clocking are distinct controls. A part may meet its bore location and still fail tooth-space orientation. Conversely, an angularly correct spline cannot excuse an unverified bore or datum face. Assign each characteristic its own measurement or acceptance basis where the print requires it.
A useful two-fixture plan shows where zero originates, how the same reference is recovered, and what check must pass before the next blanks are cut. When those three answers travel with the hub, the second setup starts with evidence instead of an assumed clock position.
Comments